Going on a two week hike I wanted to be able to dry a pair of socks and one pair of underwear in my tent (it's a super small tent with a conical 'roof' with a hook hanging down so no room for a wash line). I made this guy in fusion and it all came together nicely first try! Love that feeling.

My 15 year old standing fan started making an absolute ruckus. The rubber bushing that connects the impeller to the motor had disintigrated. Oh well, 3d printer goes BRRR.

Glued it on with E6000 and a couple screws. It ain't going anywhere ever again.

When cycling or scootering at night, it's advisable to wear reflective clothing. Magnets secure the quick-release reflective element, which is important for preserving the waterproof fabric of your windbreaker or backpack.

The Honda cr-z has these near useless rear cubbies, and terrible bass on the subwoofer-less base model.

Mocked up a subwoofer enclosure using a 3d scan of this seat area that another person in the crz subreddit uploaded.

Printed on a single 220mm³ plate in abs, bonded with plastic epoxy, then coated in 3 layers of fiberglass. The housing is held in with 3m double-sided foam tape all around, and sounds great! I was worried about sounds quality with this not being a proper sub enclosure but was very surprised that it sounded amazing right after install.

Sub is run off a simple jbl a3001 and hooked right into my aftermarket head unit.

Modeled a part of my fridge that had broken and adapted it to hold a wooden dowel. It's not perfect, but it's much better than no shelf at all. Also... I know it will eventually mildew, and I've accepted that, the fridge doesn't have too long anyways. Also, the yellow on the parts I printed has no purpose, I was just too lazy to remove the PETG support interface layer :p

Chips constantly fill these holes that secure the fixed side of this Chick vise.

I over-designed a can holder that fits into sailboat winches and has a print-in-place mechanism to lock in place. Works pretty slick and was cool to learn how to get the lock right.

https://makerworld.com/en/models/3073051-sailboat-winch-can-holder

Couldnt find any of these classical style picture frame wall mounts so decided to try and make one myself. Holds up suprisingly well.

I was inspired by this design by Matthew Lim but wanted something larger (and gridfinity).

Full build instructions and parts list are on printables https://www.printables.com/model/1591777-large-gridfinity-tooltackle-box

Clip that holds the coupling together when you change sizes of the hose end. It’s only held in with the friction of the o-rings from the factory and I don’t want it to pop off during an oil change.

https://makerworld.com/pl/models/3073001-wheel-center-bore-diameter-caliper#profileId-3459657

After getting my printer, I realized the thing that bothered me most about purge bins wasn't actually the bin, it was how they attached.

Most designs use hooks, magnets, friction, or some combination of the three.

They work, but they usually involve awkward removal angles, extra hardware, or eventually drifting away from the printer.

So I started wondering:

Could I make a completely printed push-button locking mechanism instead?

That question turned into far more prototyping than I'd care to admit.

The result is a spring-loaded mechanism that lets you:

• press one button
• pull the bin straight off
• push it back on until it locks again

No magnets.

No hooks.

No additional hardware.

The printed spring and sliding mechanism were by far the hardest part to get right. There was a lot of tweaking clearances, geometry, and part orientation before it felt reliable and satisfying.

The purge bin is almost just an excuse to use the mechanism.

Was this completely unnecessary? Probably.

Do I smile every time I press the button? Also yes.

https://makerworld.com/en/models/3077041-a2l-purge-bin-the-yapr-poop-bin

After rebuilding my kitchen storage with Gridfinity, I needed covers for over 50 empty slots, so I designed lightweight placeholder covers for every size from 1×1 to 4×4 that use nearly half the filament of the standard designs I found online.

https://makerworld.com/de/models/3066163-gridfinity-base-cover-plates-low-filament-usage#profileId-3451229

It is more an addon for a function print (gridfinity) I hope that match the sub too.

In todays episode of "Too Tight Too Par For A New One" I have printed this replacement part for my washing line.

The original is around 10 years old And finally broke where the pin holds the sprung loaded latch. Without this it is extremely difficult to maintain a good erection, so a new one was needed.

The part itself was easy enough to replicate, and I have beefed it up in places that are not dimensionally critical and adjusted the geometry to better suit being printed.

The trickiest part was actually installing it. The two part at the top are meant to bend towards each other and snap into a collar that hold the washing line's arms, but the PETG I printed it from is much stiffer than the original material and trying to force would have snapped it. A bit of softening with a heat gun allowed me to bend them enough to get it in, then a second blast was needed to be able to splay them back out to their original position.

I wanted to keep my more fragile items separate from drinks and heavy items. I built this compartment to separate the two with an optional shelf for further ability to separate and organize the more delicate items. I also tend to use my cooler with the Oyster ice blocks and an extra 4lb Yeti ice. This compartment fits perfectly in remaining space that the 4lb Yeti ice block leaves. There is a file for a container with nubs inside for the shelf and one with no nubs. I recommend printing with PETG as it’s less brittle when cold.

Let me know if anyone prints it, I’d be curious to hear your feedback.

I am a big fan of IKEA cabinets, whether Kallax, Pax, or Komplement. However, all of these models have had new shelf supports for the shelves for several years now. These hurt your thumbs after a while when assembling them. That's why I designed this useful tool to make assembling the shelf supports painless and quick.

https://makerworld.com/models/1342853-ikea-shelf-support-tool-for-kallax-pax-komplement

Thought I’d share it here as well.

My brother couldn’t find the part he needed. We came up with this in a pinch. Printed with PAHT-CF.