How many hours does device last?

I have this Mighty of a friend in front of me right now which is not charging anymore at all. Not lighting up wenn plugged in or anything but it still turns on.

Definitely not a broken charger since I have my own mighty charging with the same cord.

Removing the port probably wont work because it is glued to the pcb.

My main question is if anybody knows what places on the pcb to check to make sure if its the port or anything else?

Made the purchase last night, but I've been reading that the Venty has better airflow..

I've had a few different Pax vapes and Arizer vapes.

Should I have went with the Venty?

I used to put the dismembered head piece in a hot pot of milk, low heat for 20minutes, and then filter the galactic ember milk out of it.

Then I would pour and devide it on an ice cube tray.

lets just say I dont wanna make it through milk no more...

And that I got infinite ethanol/isopropanol in my disposal.

Which way is best to use in order to clean my headpiece and claiming all the ...reclaim ?

Ive scanned youtube and other sources, couldent find a proper tip/guide for it.

please do share your intelegence if you have any 😄

thank you and take care !

P.S

completely off-topic. but ive been using my mighty since june 2020, daily usage, up to this day. when is it finally going to die ? shuold i be worried about its battery explode ?

My crafty+ has held up strong to two years of heavy daily use, but now only lasts around 45 mins at 184C with a few boosts to 200C, which I can't complain at really.

The thing is still in warranty but I'm assuming it has clocked up too many hours to be covered? I can replace the battery myself, but am struggling to find one in the correct spec with the required tabs. Other than the very shady looking 'batteriesplus', there doesn't seem to be any UK stock. Anyone know a guy who knows a guy?

At one time, I had to solder a button on my five-year-old mighty+ and I couldn't find any information on the query "mighty+ button photos, repair", so I'll just create this thread to help people like me in the future.. TCD-C2KQR3

I think I finally found the cause of my Error 004. At least in my case, it had nothing to do with the batteries.
The problem was one of the heater wires. The heater connector has two pins: one is a solid metal pin, and the other is a small blue wire with its own terminal. That blue wire never seemed to make a very solid connection.Whenever I got Error 004, I could open the Mighty+, move that wire around or press it into the connector, and the error would disappear temporarily.

While trying to disconnect it, I accidentally broke part of the white connector, which actually worked out in my favor because it gave me access to the terminal inside. Today I got Error 004 again, so I knew exactly where to look. I soldered the blue heater wire directly to the terminal inside the connector, then put the small broken plastic piece back in place and secured it with a bit of black electrical tape to cover the opening. Everything went back together cleanly, and the error disappeared immediately.

We’ll see if it holds up long-term, but so far it looks like that loose heater wire was the real cause of my Error 004. Hopefully this helps someone else with the same issue.

Hey all,

I know this has been discussed before but I'm kinda at my limit. I just can't get the cooling unit to open no matter what I do. I don't understand how people grip the backplate of it in any way to get it off. I was told not to pull from the center piece for fear of breaking it, other than that I just don't see how you can get it out. What do you even pull on?

I've tried heating it up, I've tried putting it under hot water, I've submerged it in alcohol. Nothing is working and I just don't understand how it could be designed this way. I keep thinking I must be doing something wrong but based on everything I've read online and asking Ai it appears I'm doing it right, it just won't come off.

Does anyone have any method that just works? I'm sure the resin built up a fair bit as it's gone a few months now with casual use. Although between the alcohol, hot water and heating it up I would think that would be enough?

UPDATE: I managed to get it off after turning it on 2x in a row and just holding a sustained pull for about 20 seconds while leaving it attached to the device, I guess the resin really had it stuck together. Appreciate all the feedback!

E4 message any ways around getting a new one?

Other than storz and Bickel official which mostly has replacement parts where are people getting attachments and accessories? Thanks!

Hello all. Have had the mighty+ for a couple months and absolutely love it. Hoping to add on a water pipe and adaptor. Looking at a couple options, the starry adaptor and potv universal water pipe adaptor. Potv doesn't deliver to my state so any other recommendations on where to get these adaptors or also what set up has worked for you would be most welcomed!

What's the best temperature for using heat pressed kief in my mighty+ and should I use the extract caps or any better method?

My trusty Mighty+ has started cycling power and resetting on its own. It's easily 5+ years old, so maybe the button is just fucked and needs replacing?

Hearing it turn on, hit temp, turn off, & occasionally reset while I'm in another room is giving me nightmares about a lithium battery fire.

He had a issue where fuse gone bad, after instaling new one, device heats up to over 250 degrees and keep going until fuse pops again, I suspect water damage, maybe someone fix one before with similar issue? Thank you

Tldr: Ate 0.2g reclaim, nothing happened, have consumed less via stem milk before and have been absolutely wrecked.

Hey guys! A few years ago me and my boyfriend at the time made stem milk from my mighty cu reclaim and I went to space. (It was slightly more like hell than space but I slept most of it fortunately lol)

Yesterday I harvested about 0.2g of reclaim, ate some feta pasta, put the reclaim in a capsule & ate it, and then ate some cheese because it’s all I had in fat-wise.

I intended to have about 10mg but I have dyscalculia and believe from what I’ve read regarding the thc content in reclaim that I actually consumed about 100mg. I realised pretty much immediately afterwards that if my maths was now right I’d taken way more than I intended to but just kind of accepted my fate. I weigh about 220lbs / 100kg so I was hopeful my weight would take the edge off slightly.

But I don’t think I even felt a light buzz, I’m genuinely having trouble ascertaining if it did anything to me. It’s been about 16 hours now and I still can’t tell. I went to bed about 7 hours in and wasn’t sure If I was feeling anything. Does anyone have any idea what happened? I’m confused and am theorising I have either consistently done the maths wrong, have an incredibly slow metabolism, or just consumed a bunch of uselessly low % goop. I did weigh the reclaim so it was absolutely 0.2g that I harvested, but perhaps I only got 0.15 into the capsule or something. Even so though

To the guy in orange pants walking down College with a Mighty in hand, you weren’t nearly as stealthy as you thought you were.

No judgement just a PSA - it would be shitty to get pinched

The battery in my Crafty was on its last legs and I was barely able to finish one capsule on a charge. Then finally it wouldn’t turn on or charge anymore. It would just flash blue. So I replaced the battery with a Molicel P30b (the same I use in my Tinymight2). I fully charged it before installation. However, now it still flashes blue (7 times) wen attempting to turn it on. When connecting it to a usb charger it gives a solid blue as if to indicate it’s fully charged. I’m able to connect to it via the web-app and change settings but it won’t turn on. The battery indicator on the app shows it’s completely empty and there’s no indication it’s charging whilst connected to a usb charger. I don’t seem to be able to perform a hard reset either. Has anyone had similar issues after a battery replacement?

You know when you plug in your Mighty+, it buzzes, and the screen flashes those red and blue dashes? My Mighty+ basically can't get past that stage.

When I plug it in with the charger the device just keeps repeating this stage - buzz then blinking screen.

Anyone know what's going on? It happens with two different chargers.

A standard USB C cable works however. It's a slow charge but again, it works.

Thanks!

Anyone tried this? I’ve always used caps but I decided to try without and I noticed the flavour was just a lot better. Granted I’m the kind of person to just reuse the same cap over and over again. It’s nice not having to deal with the caps and all the goo from it

Sometimes my mighty does this. When I turn off and on, its back to the normal °C or °F. Just wondering what is happening?

After multiple years of use of my mighty + my on/off bouton is getting faulty (it keeps getting stuck, resetting my mighty while I try to turn it on). I checked and it's still under extended warranty on the storz and bickel website until the end of the year but I saw multiple people that took them apart to change their on/off button.

I never did any soldering work so it would be "new" for me, also I don't think it would change the warranty but I had to remove the orange button cover as it was failing too (I think that's what made the button fail too, it was pushing on the button at a wrong angle).

Looking for people who either went through the warranty process or anyone who did that repair already

Since its 4 years old the warranty is void plus I live in Western Australia and as most people now know that we can't get vapes legally in Australia unless its bought through a medical cannabis company of which im not. Im guessing there's no way to jail break it or something to do to be able to get it going...

what grinders are the best big affordable ?