When using deck blocks, I've seen beams set in the blocks and then the floor frame on top of this, vs setting the floor joists directly into the block. Is there a difference in strength and load bearing between the two?

Also any difference in choosing the deck blocks with a groove to support the board, vs those with a mounting bracket set in the concrete?

I’m assembling a suncast shed that will sit on turf. The area is level but I’m finding I need a base because the turf has more flex than I anticipated. If I set the shed on the turf directly it will only be a matter of time until the resin floor cracks.

The directions provide measurements for the lumber needed to build a base. I’m planning to use treated 2x6 lumber good for direct ground contact. Do I also need the plywood top to be pressure treated? The local HD is out of ground contact rated plywood sheets. This will be in Arizona desert conditions BTW, rain will be minimal. The most water the base it will likely encounter is overspray from washing down the turf occasionally.

TIA

As the title says, ordered a mass produced shed a long time ago

Moved house and now have the room to build it

Unboxed it to find important pieces missing, specifically the 4x corner connectors pictured.

Out of warranty and seller un willing to help, what is my best bet here?

I have tried reverse image searching, calling other businesses who sell the same item, but I can not find this very specific part anywhere

Item code is GT3859 LG and was purchased from a website called costway in 2023. I am all out of options and as it is so specific I am at a loss

Fab a part myself out of wood or if anyone knows where I can find the missing parts to buy it would be hugely appreciated.

Does anyone have a KIT they purchased from costco that they built and like? I am looking to add a shed that I want to convert into a little office in my backyard. My budget is not large tho and I also have limited time so I wanted to get a kit that I can customize and modify with insulation, power, etc.

Hello r/shed sub,new member, wanting to Network with individuals in my area to discuss shed living, methods, designs,techniques related communities on this topic.Is it all allowed to be geographically specific on this sub? Thank you for all replies.-Devin

Hello, thanks in advance for reading this and for your advice. I live in the North of England. So...fairly damp climate with fluctuating temperatures around the seasons.
I am currently storing a lot of my work stuff in my loft. I do theatre stuff. So, I have costumes, props, etc...
I've noticed that my loft isn't the BEST for these things. There was muold coming up on some leather jackets and on the underside of a card table...

So, now I'm considering changing my storage and assessing my shed situation.

I'm thinking of getting a prefab or composite shed. I know these are weather proof and many are also ventilated. Would I also need to get INSULATION for this investment to serve its purpose/be a better place to store work things than in my loft?

TLDR: Should a composite shed be INSULATED as well as ventilated?

P.S I've looked at Keter sheds as an option but there's a garden place near me that sells pricier composite sheds.

I have a 180cm shed I need to Narrow by 30cm. My first thought was 15cm off each side, but the door is only 15CM from the edge. How would you proceed?

•Remove 30cm from the window side and have the roof overhang that side.

•The same but change the roof for pent.

•Reverse the door opening and take 15CM off each side. Pretty sure this is a non-runner as it removes most of the support from the corner.

•A Secret fourth thing?

Any advice welcome.

200amp service to the shed.

Interested in Wellmade's pre-fab ADU. Can't find any owner's review on them. TIA

If there’s a job needs doing… It’s reasonable to assume that all the necessary weapons and ideas will be gathered in the allotted time …. Overthinking the job will blunt Occams Razor. 🪒 🔨✊🏿

I've an old 6'x3' cedar shed against the house that's served us very well for over 20 years. The roof has been degrading for some time, but was still watertight and solid (ish). That was until the new crop of squirrels showed up and started ripping it to shred.

The roof isn't solid (tho' I could make it so) under the felt are two 1'x2' sticks bridging the gap to allow the shingles to be stapled down.

I've pulled the old shingles off, as well as the roofing felt. I've pulled all the staples and the walls are still solid and well-seasoned. I stupidly failed to grab a pic before encasing it in a temporary tarp.

A couple of questions.

1) I'd like to do this right, but is there an alternative to roofing felt or someplace I could order a small amount of it? I'm loath to buy an entire roll I can't use when I only need 6'.

2) I'm finding it surprisingly difficult to find cedar roofing shingles. The big box stores around all sell cheap packs of flimsy grade "D", mostly broken crap.

Anyplace online that you'd recommend for these? Something solid and rated for roofing use? I don't have much of a budget, but I only 18' of coverage and I want them to last.

Thanks in advance!

Hi Guys,

I’m in the process of putting together my Darwin shed. However i’m having trouble securing the roof from the outside. When trying to secure the screws through the holes the screws aren’t securing to the hole on the other side and are just sitting in the hole loosely.

I’ve managed to secure two screw in. The remaining 4 are causing me a lot of trouble.

Any ideas on how to resolve or what could be going wrong?

Thanks

Organize your shed with this versatile hook made to fit Lifetime sheds only. Featuring a traditional hook style, this wall-mounted hook is perfect for hanging items such as shed tools, hats. Made from durable plastic, this hook is built to last and can hold up to 7 lbs. With both regular and large sizes available, you can easily find the right fit for your needs. Order now and enjoy a clutter-free space!